Documents

s71500_et200mp_product_information_en-US_en-US.pdf

Description
© Siemens AG 2013 - 2014. All rights reserved A5E31876033-AE, 08/2014 1 SIMATIC S7-1500/ET 200MP Amendments to documentation S7-1500/ET 200MP Product Information Introduction Scope of validity of the product information This product information supplements the documentation for S7-1500/ET 200MP and takes precedence over our system manuals, function manuals and manuals. Security information For the secure operation of Siemens products and solutions, it is necessary to take sui
Categories
Published
of 3
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Related Documents
Share
Transcript
    © Siemens AG 2013 - 2014. All rights reserved A5E31876033-AE, 08/2014 1   SIMATIC S7-1500/ET 200MP Amendments to documentation S7-1500/ET 200MP Product Information Introduction Scope of validity of the product information This product information supplements the documentation for S7-1500/ET 200MP and takes precedence over our system manuals, function manuals and manuals. Security information For the secure operation of Siemens products and solutions, it is necessary to take suitable preventive action (e.g. cell protection concept) and integrate each component into a holistic, state-of-the-art industrial security concept. Third-party products that may be in use should also be considered. You can find more information about industrial security on the Internet (http://www.siemens.com/industrialsecurity). Supplement to documentation S7-1500/ET 200MP S7-1500/ET 200MP - Marine approval Certificates for marine approval are available for SIMATIC S7-1500/ET 200MP. The certificates can be found on the Internet (http://support.automation.siemens.com/WW/view/en/56926743/134200). S7-1500/ET 200MP - Calibration of analog modules The Calibration function (calibration in RUN) is only possible with the following configurations. Module/module name Configuration Article no.: AI 8xU/I/RTD/TC ST QI 1 x 8-channel with value status 6ES7531-7KF00-0AB0 AI 8xU/I/RTD/TC ST 1 x 8-channel without value status AI 8xU/I HS QI 1 x 8-channel with value status 6ES7531-7NF10-0AB0 AI 8xU/I HS 1 x 8-channel without value status AQ 8xU/I HS QI 1 x 8-channel with value status 6ES7532-5HF00-0AB0 AQ 8xU/I HS 1 x 8-channel without value status AQ 4xU/I ST QI 1 x 4-channel with value status 6ES7532-5HD00-0AB0 AQ 4xU/I ST 1 x 4-channel without value status AI 4xU/I/RTD/TC/ AQ 2xU/I ST QI 1 x 6-channel with value status 6ES7534-7QE00-0AB0 AI 4xU/I/RTD/TC/ AQ 2xU/I ST 1 x 6-channel without value status AI 4xU/I/RTD/TC ST QI 1 x 4-channel with value status 6ES7531-7QD00-0AB0 AI 4xU/I/RTD/TC ST 1 x 4-channel without value status AQ 2xU/I ST QI 1 x 2-channel with value status 6ES7532-5NB00-0AB0 AQ 2xU/I ST 1 x 2-channel without value status    Amendments to documentation S7-1500/ET 200MP 2  A5E31876033-AE, 08/2014 S7-1500/ET 200MP - Configuring You can configure the following modules with STEP 7 (TIA Portal) as of V13.0.0 with HSP0102 or with a GSD file. Module Article number AI 4xU/I/RTD/TC/ AQ 2xU/I ST 6ES7534-7QE00-0AB0 AI 4xU/I/RTD/TC ST 6ES7531-7QD00-0AB0 AQ 2xU/I ST 6ES7532-5NB00-0AB0 S7-1500/ET 200MP - MSI/MSO The function Module-internal Shared Input / Shared Output (MSI/MSO) can be configured with the GSD file. Configuration with STEP 7 (TIA Portal) is possible starting from V13, Update 3. S7-1500/ET 200MP with PtP modules - Parameter assignment of data flow control Communication may come to a standstill when you use communication modules with RS232 interface, if the following hardware data flow control was configured: ●   Hardware RTS always ON ●   Hardware RTS always ON, ignore DTR/DSR The behavior occurs for the following communication modules with firmware version V1.0.0: ●   CM PtP RS232 BA (6ES7540-1AD00-0AA0) ●   CM PtP RS232 HF (6ES7541-1AD00-0AB0) The behavior of the modules has been remedied as of firmware version V1.0.1. S7-1500/ET 200MP - Use of PTC resistors PTC resistors are suitable for temperature monitoring of electrical devices, such as motors, drives, and transformers. Use Type A PTC resistors (PTC thermistor) in accordance with DIN/VDE 0660, part 302. In doing so, follow these steps: 1.   Choose Resistor (2-wire terminal) and PTC in STEP 7. 2.   Connect the PTC using 2-wire connection technology. If you enable the Underflow diagnostics in STEP 7, it will be signaled for resistance values <18 Ω. In this case, this diagnostic signifies Short-circuit in the wiring . The following figure shows the address space assignment for analog modules with PTC resistors. Figure 1 Assignment of the address space for analog modules with PTC resistors    Amendments to documentation S7-1500/ET 200MP A5E31876033-AE, 08/2014 3   ET 200MP with IM 155-5 PN ST Channel diagnostics In contrast to the order specified in the manual, the User Structure Identifiers (USI) are structured as follows: ●   USI data block ●   Reserved bytes ●   Manufacturer-specific diagnostics MSI/MSO As of firmware version V2.0.0, the IM 155-5 PN ST interface module supports the module-internal Shared Input/Shared Output (MSI/MSO) function with up to two IO controllers. ET 200MP with IM 155-5 DP ST Operation on Y-link As of firmware version V2.0.0, the IM 155-5 DP ST interface module can be operated as DP slave after the Y-link. Technical specifications For the IM 155-5 DP ST, the address space of each module can be assigned a maximum of 64 bytes of inputs and a maximum of 64 bytes of outputs. ET 200MP with IM155-5 PN HF - Shared Device In contrast to the information in the ET 200MP IM155-5 PN HF manual, you cannot use the shared device function with more than 2 IO controllers. ET 200MP - Response times Additional information about performance measurements is available on the Internet (http://support.automation.siemens.com/WW/view/en/34677186/136000&cspltfrm=0&cssw=0&csbinh=5). S7-1500 CPU 1517-3 PN/DP Note Use of the 2nd PROFINET interface X2) for communication with a configuration system In the S7-1500 CPU 1517-3 PN/DP manual, section 2.2 Properties , the term configuration system refers specifically to the TIA Portal.   Amendments to documentation S7-1500/ET 200MP A5E31876033-AE, 08/2014 Siemens AG Industry Sector Postfach 48 48 90026 NÜRNBERG
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks