Documents

Mazak M32 Parameters and Alarms.pdf

Description
Description:
Categories
Published
of 231
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Share
Transcript
  Alarm & Parameter Manual for Mazatrol M-32 Series Publication # C731SA0551E  5/95 CAUTION:  ãThis manual is published to assist experienced personnel in the operation, maintenance and/or programming of Mazak machine tools, and is not intended to be used as training documentation.ãAll Mazak machine tools are engineered with a number of safety devices to protect personnel and equipment from injury or damage. Operators should not, however, rely solely upon these safety devices, but should operate the machine only after fully understanding what special precautions to take by reading the following documentation thoroughly.ãDo not attempt to operate or perform maintenance/repair on the machine without a thorough understanding of the actions about to be taken. If any question exists, contact the nearest Mazak service center for assistance.ãCertain covers, doors or safety guards may be open or removed to more clearly show machine components. These items must be in place before operating the machine. Failure to comply with this instruction may result in serious personal injury or damage to the machine tool.ãThis manual was considered complete and accurate at the time of publication, however, due to our desire to constantly improve the quality and specification of all Mazak products, it is subject to change or modification.  ALARM & PARAMETER MANUALforMAZATROL M-32 SERIESCONTENTS Page 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11-1 PURPOSE OF THIS MANUAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11-2 MAZAK CUSTOMER SUPPORT NETWORK. . . . . . . . . . . . . . . . . . . 1-21-3 LIST OF RELATED DOCUMENTATION. . . . . . . . . . . . . . . . . . . . . . 1-3 2. USING THE NC ALARM LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12-1 MACHINE STATUS INDICATOR LAMPS. . . . . . . . . . . . . . . . . . . . . . 2-12-2 ALARM DISPLAY & CLEARING PROCEDURE. . . . . . . . . . . . . . . . . 2-12-3 NC ALARM LIST STRUCTURE. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 3. MAZATROL M-32 ALARM LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13-1 NC SYSTEM CPU ERRORS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13-2 AXIS & SPINDLE DRIVE ERRORS. . . . . . . . . . . . . . . . . . . . . . . . . . 3-53-3 CNC & MACHINE PLC CONTROL ERRORS. . . . . . . . . . . . . . . . . . 3-193-4 DISPLAY OPERATION ERRORS. . . . . . . . . . . . . . . . . . . . . . . . . . 3-533-5 DATA I/O ERRORS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-633-6 AUTO CYCLE MODE PROGRAMMING ERRORS. . . . . . . . . . . . . . 3-853-7 TOOL PATH MODE PROGRAMMING ERRORS. . . . . . . . . . . . . . 3-113 4. USING THE NC PARAMETER LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14-1 DESCRIPTION OF THE NC PARAMETER LISTS. . . . . . . . . . . . . . . 4-14-2 DISPLAYING PARAMETER DATA. . . . . . . . . . . . . . . . . . . . . . . . . . 4-34-3 NC PARAMETER LIST STRUCTURE. . . . . . . . . . . . . . . . . . . . . . . . 4-4 5. MAZATROL M-32 PARAMETER LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15-1 CUTTING CONDITIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15-2 USER PARAMETER (Point Cutting). . . . . . . . . . . . . . . . . . . . . . . . . 5-35-3 USER PARAMETER (Line/Face). . . . . . . . . . . . . . . . . . . . . . . . . . 5-175-4 USER PARAMETER NO. 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-335-5 USER PARAMETER NO. 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-435-6 USER PARAMETER NO. 3 & 4. . . . . . . . . . . . . . . . . . . . . . . . . . . 5-575-7 MACHINE CONSTANT PARAMETERS. . . . . . . . . . . . . . . . . . . . . . 5-61 *  NOTE:Alarms 200-399 are PLC (programmable logic control) generated for aspecific machine application and may vary from machine to machine. If theerror description is insufficient to correct the problem, make note and contactyour regional service center for assistance. C731SA0551E5/95C-1  Notes:C-2
Search
Tags
Related Search
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks
SAVE OUR EARTH

We need your sign to support Project to invent "SMART AND CONTROLLABLE REFLECTIVE BALLOONS" to cover the Sun and Save Our Earth.

More details...

Sign Now!

We are very appreciated for your Prompt Action!

x