Documents

7F132AB931D3492BA0749355F3A58EBE[1].pdf

Description
Installation Guide RGS, RGSR, RGSF, RGSK AND RGSbtb B OK 60 1 Measure the opening and check that the measurement is within the tolerance range 120.5 mm +/- 0.5 mm. Check that the frame isclean and pull through the cables. Measure the diameter of the cables and choose suitable blocks. Lubricate the inner faces of the frame. A 2 Insert Block. The blocks are identified by their width (A) and hole diameter (B). A block that is 30 mm wide and has a hole diameter of 18 mm is marked 30/18. This ma
Categories
Published
of 2
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Related Documents
Share
Transcript
  Pressure-tight installation in frames RGS, RGSC, RGSF, RGSK, RGSR and RGSbtb Installation Guide RGS, RGSR, RGSF, RGSK AND RGSbtb LB 258 GB 2013 V.1 1/2 Check that the frame is clean and that  the inside is well lubricated. All Lycron parts must be lubricated carefully with MCT Brattberg lubricant.Place the compression plate in the cen- tre so that the Lycron rubber is pushed upwards between the compression plate and the frame.The seal must not be subjected to pressure for at least 48 hours after installation. This is to allow the pressure  to equalise throughout the penetration.It will take more time for the pressure  to equalise at temperatures below 20°C. Note: If the installation is subjected  to pressure, all components must be replaced after removal and refitting.  Insert Block. The blocks are identified by their width (A) and hole diameter (B). A block that is 30 mm wide and has a hole diameter of 18 mm is marked 30/18. This marking is cast into the block. Pack the frame. Place stayplates betweeneach row of blocks. The diagram marked OK shows how the cable should look when correctly fitted. Insert the compres-sion plate in the framebefore the top row of blocks. Insert the top row of blocks. Insert the STG end-packing with the tonguearound the compression bolt. Tighten the nuts in theendpacking until 12-15 mm of thread is visible. Tighten the bolt in the compression plate anti-clockwise until there is a gap of 32-33 mm between the top of the plate and the insi-de of the frame. Then fit the PTG presswedge over the stay-plates. Place the last two stayplates in the framebefore the last row of blocks. Insert the final row of blocks. Tighten the nutsin the PTG until 12-15 mm of thread is visible. STG ENDPACKINGPTG PRESSWEDGE 2  Measure the opening and check that the measurement is within the tolerance range 120.5 mm +/- 0.5 mm. Check that the frame isclean and pull through the cables. Measure the diameter of the cables and choose suitable blocks. Lubricate the inner faces of the frame. 1 5567  The PTG press-wedge can be placed anywhere in the frame. 867834 Place the shaped corner blocks at the bottomof the frame. Then continue as shown in figure 4 and under STG ENDPACKING in figures 5-7Fit the C-STG endpacking (with rounded corners). Place the tongue around the bolt first. Tighten the nuts on the endpacking until 12-15 mm of thread is visible. RGSCRGSC Place the shaped corner blocks at the bottom of the frame. Then continue as shown in figure 4Fit the PTG presswedge in one of the rowsbetween the top and bottom row. Finish by inserting the two upper special corner blocks, then the rest of the blocks in that row. Tighten the nuts in the PTG until 12-15 mm of thread is visible. 60 AB OK  www.mctbrattberg.com  U-Block AddBlock Plug Check that the frame is clean and pull through the cables.  Measure the diameter of the cables and choose suitable blocks. Lubricate the inner faces of the frame.Select a suitable standard Block or AddBlock for the small cable. Then create a base using U-Blocks. The external measurements should be the same as the previous block.Choose an AddBlock suitable for the cable diameter.The centre plug is a snug fit for any pre-selected AddBlock since its diameter i adjustable - all thanks to the wraparound casing.Place the plug in the AddBlock and make sure the locking devices secure it in place.Start packing the frame.Tear off attached sheet to fit the dimension selected. Place sheet into centre slot and affix it with the unique locking device.Tear off superfluous sheets. Insert stayplates between each row of insert blocks.Select a suitable block for the largest cable in the row. PREPARING FOR A FUTURE INSTAL-LATION.  Measure the opening and check that the measurement is within the tolerance range 120.5 mm +/- 0.5 mm. Measure the opening and check that the measurement is within the tolerance range 120.5 mm +/- 0.5 mm. Check that the frame is clean and pull through the cables. Measure the diameter of the cables and choose suitable blocks. Lubricate the inner faces of the frame. www.mctbrattberg.com LB 263 GB 2013 V.1 2/2
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks