Music & Video

Canvas Office Landscape Work Surface, D-Top and Peninsula Installation and Disassembly for Recycling Instructions

Description
Y Canvas Office Landscape Work Surface, D-Top and Peninsula Installation and Disassembly for Recycling Instructions Notice With FORMCOAT work surfaces, if any screw is to be relocated for any reason, a
Categories
Published
of 13
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Related Documents
Share
Transcript
Y Canvas Office Landscape Work Surface, D-Top and Peninsula Installation and Disassembly for Recycling Instructions Notice With FORMCOAT work surfaces, if any screw is to be relocated for any reason, a 1/8 X 5/8-3/4 pilot hole MUST be drilled at a new location. Notice Herman Miller, Inc., will not under any circumstances guarantee or assume responsibility for loading performance beyond individual component load capacities listed below.! WARNING Load capacities as listed below for work surface include the total load of fully loaded components attached to the underside of the work surface plus the load placed on the top of the work surface. Failure to observe the recommended practices, such as loading beyond the capacities, will result in unsafe usage conditions and may result in failure of components and personal injury. CAUTION! e sure all work surface supports being used to support the same work surface are installed at the same height. Work surface load capacities upto and including 48 width: for 30 depth pounds for 24 depth pounds for 18 depth pounds Work surface load capacities from 48 up to and including 96 width: for 24 depth with three work surface supports or two work surface supports and two work surface support clips pounds. for 30 depth with three work surface supports pounds. for 24 and 30 depth with four work surface supports pounds with half of the load bearing on each half of the work surface. Curvilinear work surface load capacities up to and including 96 width: depth pounds depth pounds Recommended support bracket sizes for curvilinear work surfaces: 24 Deep Side 30 Deep Side End Supports Center Supports Heavy Duty Heavy Duty 2013 Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. Y, and Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc. 1 Parts Included: A Work Surface (FT L shown) Center Support C Pan Head Tapping Screw D Support LH E Support RH F Pan Head Tapping Screw (needed when support is used as center support) G Ganging Plate H Pan Head Tapping Screw (4) Tools Required: Power Driver #2 Phillips it 5/32 Hex Key Level Safety Glass 2013 Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. Y, and Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc. 2 Note: Install Wall Cladding before installing work surface supports. Assembly Instructions: D or E Hooks Tab 2 1. Tilt support ( D shown). Insert tab into slot in frame at desired height. 2. Rotate support downward until all hooks are in slots. 3. Push down on supports until all hooks engage into slots. 4. Repeat installation for other support ( E ) 2013 Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. Y, and Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc. 3 Notice Only standard center supports are to be used with curvilinear and all FORMCOAT work surfaces regardless of width. 2 D or E Center Support for 60, 66 & 72 wide laminate rectangular work surfaces only. Center Support for 78, 84, 90, 96 wide & 60 thru 96 wide Formcoat and HPL curvilinear work surfaces only. Center Support for 60, 66 & 72 wide HPL rectangular work surfaces only. Center support for 78, 84, 90, 96 wide & 60 thru 96 wide Formcoat and HPL curvilinear work surfaces only. 1. If work surface is 68 or 72 wide, install center support on center frame style at same height as work Surface Supports. If Work Surface is 78, 84, 90 or 96 wide, install Standard Center Support ( D and/or E ) on frame styles at same height as Work Surface Supports. D or E D or E 2013 Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. Y, and Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc. 4 3 Shoulder Screw Keyhole Slot Hole A 1. Install work surface (A) by inserting Shoulder Screws into Keyhole Slots in rear of Work Surface Supports. Push Work Surface back until front Spacers engage front holes in Supports. If Work Surface is 84, 90 or 96 wide, Shoulder Screws and front Spacers must also engage in heavy duty Center Supports. 2. Level Work Surface by adjusting Set Screw in Support. Center Support C 3. On 60, 66 & 72 wide Work Surface, Align Center Support with center of Work Surface. Secure Center Support with Screw (C) supplied with Support. For 78, 84, 90 & 96 wide Work Surfaces with heavy duty Center Support, install Screw (F) supplied with heavy duty Center Supports Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. Y, and Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc. 5 4 G H 1. Install Ganging Plate (G) between adjacent Work Surfaces with (4) Pan Head Screws (H) 2013 Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. Y, and Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc. 6 D-Top and Pennisulas Work Surface Installation Products Included: Parts Included: FT231. A D-Shaped Work Surface C Pennisula Work Surface FT230. J Extended Corner Pennisula Work Surface Tools Required: FT224. FT225. IMPORTANT: Save these instructions for layout changes Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. Y, and Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc. Power Driver #2 Phillips it Level Safety Glass 7 Parts Included: Extended Corner D Peninsula rackets K E Peninsula rackets Ganging Plate Support Leg x 7/8 lg x 3/4 lg F Tapping Screw (8) G Tapping Screw H Assembly Instructions: Pan Head (8) Sems Screw Pan Head, Ext Tooth Washer (4) 1 Support Leg Installation 1. Place work surface (A) face down on clean padded surface. 2. Align holes in Support leg () with pre-drilled holes in work surface (A) and secure with (8) screws (F). Note: Make sure no weld side of leg faces out. 3. Torque screws to 45 in/lbs. Weld Side No Weld at Front A No Weld F 2013 Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. Y, and Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc. 8 2 Ganging Plate Installation 1. Mount Ganging Plate (E) to D-top (A) with four (4) screws (G). 2. Torque screws to 45 in/lbs. 3. Repeat for opposite end. E A G 3 D-Shaped Work Surface Installation 1. Set D-top (A) upright and align with adjacent work surfaces, maintaining 1/8 gap between D-top and adjacent work surfaces. 2. Using Ganging Plate (E) as a template, drill four(4) 1/8 x 1/2 pilot holes in underside of adjacent work surface. Secure ganging plate with four (4) screws (G). 3. Torque screws to 45 in/lbs. 4. Repeat for opposite side. A 1/8 Gap G Pilot Holes E 2013 Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. Y, and Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc. 9 4 Peninsula Top Installation 1. Attach Support leg () to Peninsula top (C) as shown in step Install Peninsula racket (D) into Frame by inserting tab on top hook of bracket into frame slot at desired height. Rotate bottom of bracket into slots in frame to engage all hooks. 3. Repeat for opposite side. C D Frame Engage all Hooks 4. Set peninsula (C) upright and position unsupported end cover brackets (D). H D 5. Align outer screw holes in brackets (D) with pilot holes in Peninsula top (C). Secure with four (4) screws (H) Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. Y, and Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc. 10 5 Extended Corner Peninsula Work Surface Installation 1. Insert either RH or LH Peninsula racket Tab (K) into Slot in Frame. Rotate down engaging both hooks into frame. Make sure racket is installed at same height as adjacent work surface. Tab K Hooks 6 Support Leg Installation F J 1. Place Work Surface Top (J) face down on a clean padded surface. 2. Attach Support Leg () to Work Surface Top with 8 Screws (F) Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. Y, and Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc. 11 7 Cantilever Installation Shoulder Screw J Spacer Keyhole Slot Hole Surface Cantilever 1. Install Shoulder Screw and Spacer supplied with Surface Cantilever. 2. Install Surface Cantilever to Frame. See instructions supplied with Surface Cantilever. 3. Install Work Surface (J) by inserting Shoulder Screw into keyhole Slot in rear of Surface Cantilever. Push Work Surface back until front Spacer engages front hole of Surface Cantilever. 8 Peninsula racket Attachment K H 1. Attach Peninsula racket (K) to Work Surface using screw (H). 2. Level Work Surface by adjusting Set Screw in Cantilever and by adjusting Glides Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. Y, and Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc. Glides Set Screw 12 Disassembly for Recycling: Materials Identification and Segregation: Where possible, plastic components are marked with ASTM recycling codes. Use these codes to identify material type for recycling. Non marked components should be treated as mixed plastic. Ferrous metals can be identified using a small magnet for recycling. Non-ferrous metals should be separated and recycled separately. To disassemble product, reverse the above installation steps Herman Miller, Inc. eeland, Michigan. Printed in the U.S.A. Y, and Canvas Office Landscape are among the registered trademarks of Herman Miller, Inc. 13
Search
Similar documents
View more...
Related Search
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks