Computers & Electronics

CP 2048 USER MANUAL. Article No: RGB-RD-UM-CP 2048 E001 Revision No: V1.0

Description
CP 2048 USER MANUAL Article No: RGB-RD-UM-CP 2048 E001 Revision No: V1.0 CONTENTS CONTENTS... 2 Declarations... 3 FCC/Warranty... 3 Operators Safety Summary... 4 Installation Safety Summary... 4 Chapter
Published
of 41
All materials on our website are shared by users. If you have any questions about copyright issues, please report us to resolve them. We are always happy to assist you.
Related Documents
Share
Transcript
CP 2048 USER MANUAL Article No: RGB-RD-UM-CP 2048 E001 Revision No: V1.0 CONTENTS CONTENTS... 2 Declarations... 3 FCC/Warranty... 3 Operators Safety Summary... 4 Installation Safety Summary... 4 Chapter 1 Your Product In the Box Product Overview Back Panel Top Panel Dimension Chapter 2 Using Your Product CP 2048 Control VENUS X Connection Select Output Port Size&Position Add Layer Save&Load Logo Capture & Load EDID Management System Mode CP 2048 Control VSP Connection Edit the Input Signal Output Resolution Setting Switch the Signal Scale Logo Capture & Load Save&Load EDID Management System Mode Chapter 3 Ordering Codes Product Chapter 4 Contact Us Chapter 5 Appendix Terms & Definitions Revision History CP 2048 User Manual 2 Thank you for choosing our product! This User Manual is designed to show you how to use this video processor quickly and make use of all the features. Please read all directions and instructions carefully before using this product. Declarations FCC/Warranty Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be responsible for correcting any interference. Guarantee and Compensation RGBlink provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults. RGBlink must be informed immediately in writing of any complains. The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of compliant, RGBlink can repair the fault or provide a replacement at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or indirect damage, and also damage attributed to the operation of software as well as to other service provided by RGBlink, being a component of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties guaranteed in writing or due to the intent or gross negligence or part of RGBlink. If the purchaser or a third party carries out modifications or repairs on goods delivered by RGBlink, or if the goods are handled incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by RGBlink either. The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the customer. CP 2048 User Manual 3 Operators Safety Summary The general safety information in this summary is for operating personnel. Do Not Remove Covers or Panels There are no user-serviceable parts within the unit. Removal of the top cover will expose dangerous voltages. To avoid personal injury, do not remove the top cover. Do not operate the unit without the cover installed. Power Source This product is intended to operate from a power source that will not apply more than 230 volts rms between the supply conductors or between both supply conductor and ground. A protective ground connection by way of grounding conductor in the power cord is essential for safe operation. Grounding the Product This product is grounded through the grounding conductor of the power cord. To avoid electrical shock, plug the power cord into a properly wired receptacle before connecting to the product input or output terminals. A protective-ground connection by way of the grounding conductor in the power cord is essential for safe operation. Use the Proper Power Cord Use only the power cord and connector specified for your product. Use only a power cord that is in good condition. Refer cord and connector changes to qualified service personnel. Use the Proper Fuse To avoid fire hazard, use only the fuse having identical type, voltage rating, and current rating characteristics. Refer fuse replacement to qualified service personnel. Do Not Operate in Explosive Atmospheres To avoid explosion, do not operate this product in an explosive atmosphere. Installation Safety Summary Safety Precautions For all CP 2048 processor installation procedures, please observe the following important safety and handling rules to avoid damage to yourself and the equipment. To protect users from electric shock, ensure that the chassis connects to earth via the ground wire provided in the AC power Cord. The AC Socket-outlet should be installed near the equipment and be easily accessible. CP 2048 User Manual 4 Unpacking and Inspection Before opening CP 2048 processor shipping box, inspect it for damage. If you find any damage, notify the shipping carrier immediately for all claims adjustments. As you open the box, compare its contents against the packing slip. If you find any shortages, contact your sales representative. Once you have removed all the components from their packaging and checked that all the listed components are present, visually inspect the system to ensure there was no damage during shipping. If there is damage, notify the shipping carrier immediately for all claims adjustments. Site Preparation The environment in which you install your CP 2048 should be clean, properly lit, free from static, and have adequate power, ventilation, and space for all components. CP 2048 User Manual 5 Chapter 1 Your Product 1.1 In the Box AC Power Cord DB9 to RJ11 Cable USB Cable Network Cable 9-pin Serial Cable Warranty Card & USB Files Screw Driver QC Declaration Note: AC Power Cable supplied as standard according to destination market. USB is contained on the Warranty/Registration Card. Please keep. CP 2048 User Manual 6 Chapter 1: Your Product 1.2 Product Overview CP 2048 control mixer is the latest full function mixer enabling the user remote control of the input selection, transition effects, and picture control of the RGBlink seamless switcher series. This allows the CP 2048 to be placed in control booth with operator who can manage all video control and mixing functions, and safety keeping the video switcher and scaler with other control systems in the equipment rack. The CP 2048 and seamless switcher can be simultaneously connected and controlled via TCP/IP, RS232 and USB connections for flexibility in system integration. This allows for comprehensive picture controls, multi layers, and more than 24 digital effects utilizing the integrated T-bar and rotary knobs along with the 3D motion joystick. Features Input selection control for Program and Preview outputs Comprehensive picture controls Transition effects, selection buttons, rotary button and T-bar Ethernet control and monitoring CP 2048 User Manual 7 Chapter 1: Your Product Back Panel Control Connectors DIP Switch Switch downward to be ON state, it works normally. Switch upward to be OFF state, it is updating. RJ45 Ethernet Connect to an isolated network. Used for communications with devices. USB-B USB Connect to an isolated communication. Used for communications with devices. DB9 RS232 Used for communications with devices. Power Connection 5 6 Power Switch Illuminated power switch. IEC Power Input Main power input AC V Max 65W. CP 2048 User Manual 8 Chapter 1: Your Product Top Panel Panel Instruction 1 Touch Screen Menu Section 5 Joystick Section 2 Presets Section 6 Destinations/AUX 3 Layer Functions Section 7 Transition Section 4 Source Selection 8 Output Control Section Touch Screen Menu Section 1 Touch Screen Four ways to access a function or a menu: --Push a button on the Touch Screen. --Push the Softkey adjacent to label. --Use NAV to move the highlight, then use ADJ. --Touch a line to move the highlight, then use ADJ. Softkeys Softkey labels (when present) appear on the Touch Screen. NAV Move the highlight up and down, or adjust the labeled parameter. ADJ Adjust the highlighted parameter. PIP Preview mode. CP 2048 User Manual 9 Chapter 1: Your Product SPLIT Standard mode. LINK Link mode. FORMAT Output format selection button. Presets Section 2 1/2/3/4/5/6 Preset to recall a controller setup a Preset ) to Preview. Each button represents a single look. Previous Jump to the previous valid preset. NEXT Jump to the next valid preset. Page Push the button, button 1~6 LED light will be on, and select the page. SAVE Push the button, button 1~6 LED light will be on, and save the preset. SHIFT CP 2048 V1.0 can not support this function. LOCK Lock front panel button. Layer Functions Section 3 Program Layers Layer 1 to layer 16. ALL Select all layers. Add Layer Add the layer. Clear Layer Clear the layer. DSK DSK setup. LOGO LOGO setup. BLACK Black out. Source Selection 4 Source Selection CP 2048 User Manual 10 Chapter 1: Your Product Each button is an input that can be assigned to a PIP or Aux destination. Green LEDs Solid: Source is on Program, associated destination is enabled. Blinking: Split is Off. Layer is on Program, opposite layer on Preview. Preview Layers Solid: Source is on Preview, layer is not active for modification. Blinking: Source is on Preview, blinking layer is active for modification. Joystick Section 5 Source Adjust source within PIP or layer. Scale Adjust the size of layers within PIP. Freeze Freeze the active layer on Program. Crop Crop boundaries of layer. Source Take active layer to full screen. Full Screen Adjust the edges and position of layers with PIP. Joystick Adjust the selected PIP. X-Axis (left/right). Y-Axis (up/down). Z-Axis (size). Z-Axis also adjusts value of highlighted parameter on Touch Screen. Interface Connect to low voltage Scrip light. Destinations/AUX 6 1/2/3/4 Push 1~4 to program IP to corresponding controlled device. ALL Push to select all destinations. Double-punch to turn all off. DEST/AUX Push to select two or more destinations simultaneously. Transition Section 7 WIPE Select WIPE as the current transition type. MIX Select MIX as the current transition type. CUT Instantly cut images from Preview to Program. CP 2048 User Manual 11 Chapter 1: Your Product WIPE and MIX effects can be assigned on a per destination basis, and performed simultaneously. AUTO TRANS Transition automatically from Preview to Program. Use Effects Menu to set transition parameters. T-Bar Manually transition sources to/from Program, based on current transition type. Output Control Section 8 Program/Preview Output Select any combination of layers on Preview. Blinking: Layer is selected and active for adjustment. Solid: Layer is selected on Preview, but is not active for adjustment. CP 2048 User Manual 12 Chapter 2 Installing Software Dimension Following is the dimension of CP 2048 for your reference: CP 2048 User Manual 13 Chapter 2 Using Your Product 2.1 CP 2048 Control VENUS X Connection Connect CP 2048 and VENUS X3 by series cable (RS232) or Ethernet cable (RJ45). CP 2048 Series Cable(RS232) Ethernet Cable(RJ45) VENUS X3 (1) Connect CP 2048 and VENUS X3 by Ethernet cable. Step 1: Open VENUS X3 network function and check IP address, the steps are as follow: Menu System Ethernet Setup Network On Menu System Ethernet Setup IP Address Step 2: Connect CP 2048 and VENUS X3 by Ethernet cable (LAN port). Step 3: Set CP 2048 IP address. 1 Touch any number button (1-4) shown as below Device No.1-4 or select by REMOTE in the touch panel menu: 2 Set up the same IP address of CP 2048 with VENUS X3: Device IP: CP 2048 User Manual 14 Chapter 2 Using Your Product (2) Use series port to connect CP 2048 and VENUS X3. Step 1: Touch any number button (1-4) as below picture or by selecting REMOTE in touch menu to select the Device. Step 2: Change to VENUS X3 connecting CP 2048 com port like COM1 in NETWORK under Device Remote menu, the step is as below figure 2. (Figure 1) (Figure 2) After being setting up, touch the number button (1-4)again, the CP 2048 will be automatically connected and sync. Note: If CP 2048 display shows Device Unconnected, please check if the previous setup, Ethernet cable or series port connection is correct or not Select Output Port CP 2048 User Manual 15 Chapter 2 Using Your Product (1) The two lines buttons are respectively referred to 8 output (two output cards) in VENUS X3. (2) Select the corresponding number button in CP 2048 for the output. Note: The output will be changed to the followings under Preview Mode. First Row:Output1, 3, 5, 7 (Program) Second Row: Output2, 4, 6, 8 (Preview) Size&Position Change size or position by the joystick and rotation. (1) Push Scale button then change size by Joystick. When the joystick is turned to right or left, CP 2048 User Manual 16 Chapter 2 Using Your Product the size will be zoomed or scaled horizontally. When the joystick is turn to up and down, the size will be zoomed or scaled vertically. (2) Push the POS button, then change the position by joystick. When the joystick is turn to right or left, the X position will be changed. When the joystick is turn to up and down, the Y position will be changed. (3) Push the CROP button, the joystick can change the crop size and position, when the joystick is turn to right or left, the size will be zoomed or scaled horizontally. When the joystick is turn to up and down, the size will be zoomed or scaled vertically. (4) FREEZE: Select the current image to touch or release the Freeze button. (5) FULL SCREEN: Select the current image to set full screen Add Layer (1) Click [Add Layer] button to add layer (Click Clear Layer button to clear layer). (2) 16 buttons are correspondingly for the 16 layers of VENUS X3, click the number buttons to open the layers. CP 2048 User Manual 17 Chapter 2 Using Your Product (3) 16 number buttons correspondingly refer to 16 inputs of VENUS X3, click number button to select the input Save&Load CP 2048 User Manual 18 Chapter 2 Using Your Product (1) Touch [SAVE] button, the bank will be saved (6 Page 6 Bank). (2) Load: Click the number button to load the bank Logo Capture & Load Select the layer and signal, push the [LOGO] button as below picture, the button will be flashing. (1) View the display and select Freeze to freeze the LOGO image. (2) Select LOGO Capture and select the number (1-10) to save the LOGO. (3) Click rotation to view if LOGO Capture is ok or not. Select the layer and signal, push the [LOGO] button shown as below picture and the button is flashing. View the monitor, select LOGO Display button to select the saved logo (1-10), click rotation to load the LOGO. CP 2048 User Manual 19 Chapter 2 Using Your Product EDID Management EDID Feature: (1) Copy the rear-end device to the VENUS X3 HDMI input to realize recognition. (2) Customized EDID can set higher resolution to realize pixel by pixel input. VENUS X3 can solve the two issue by EDID Management as below steps: (1) Click [INPUT], and find the [EDID] in bottom right and click to enter EDID. (2) For compatible issue, select to be changed signal format of source file and terminal port, click Write to change EDID (3) For pixel by pixel output, click Custom in the bottom right, enter to customized resolution CP 2048 User Manual 20 Chapter 2 Using Your Product page and click Write to change EDID System Mode Preview Mode, Standard Mode and Link Mode are supported when control VENUS X3. Preview Mode Click [PIP], make operation as below notices: (1) Shown as Figure 1 and click [YES]. (2) Shown as Figure 2, after setting up the screen parameter, click [Please to set advance and save]. (3) Shown as Figure 3, after setting up the screen parameter, click [Save to page 1_Bank 1] to enter to preview mode. (Figure 1) (Figure 2) (Figure 3) For preview mode, the bank-edit step is as below: (1) Select output in [PREVIEW OUTPUT]. (2) Select layer in [SOURCE SELECTION]. (3) Select input source in [PREVIEW LAYERS]. (4) Edit the bank by the rotation button. (5) Switch Bank to Program output by T-bar or [AUTO TRANS]. (Each output can be 4 layers at CP 2048 User Manual 21 Chapter 2 Using Your Product maximum). By T-bar or [AUTO TRANS] Standard Mode Click [SPLIT], make operation as below notices: (1) Shown as Figure 1, click [YES]. (2) Shown as Figure 2, select split mode and click [Please to set advance and save]. (3) Shown as Figure 3, set up the screen parameter and click [Save to page 1_Bank 1] to enter to standard mode. (Figure 1) (Figure 2) (Figure 3) For standard mode, the bank-edit step is below: (1) Select output in [PREVIEW OUTPUT]. (2) Select layer in [SOURCE SELECTION]. (3) Select input source in [PREVIEW LAYERS]. (4) Edit the bank by rotation. Link Mode (1) Connect output 6 and 8 to any other input (1-16) by two DVI cables independently. (2) Click [LINK] button to make operation according to the note in screen: A. As shown in Figure (1), click [YES]. B. As shown in Figure (2), select split mode and click [Please to set advance and save]. CP 2048 User Manual 22 Chapter 2 Using Your Product C. As shown in Figure (3), set screen parameter by rotation button and click [Save to page 1_Bank 1] to enter to the LINK Mode. (Figure 1) (Figure 2) (Figure 3) For Link Mode, the bank edit steps as below: (1) Select output in [PREVIEW OUTPUT]. (2) Select layer in [SOURCE SELECTION]. (3) Select input source in [PREVIEW LAYERS]. (4) Edit the bank by rotation button. (5) Switch then bank to the LED screen by T-bar or [AUTO TRANS] (5 layers at maximum). By T-bar or [AUTO TRANS] CP 2048 User Manual 23 Chapter 2 Using Your Product 2.2 CP 2048 Control VSP Connection Connect CP 2048 and VSP 5360 by series cable (RS232) or Ethernet cable (RJ45). CP 2048 Series Cable(RS232) Ethernet Cable(RJ45) VENUS X3 (1) Connect CP 2048 and VSP 5360 by Ethernet cable. Step 1: Open VSP 5360 network function and check IP address, the steps are as follow: Menu System Ethernet Setup Network On Menu System Ethernet Setup IP Address Step 2: Connect CP 2048 and VENUS X3 by Ethernet cable (LAN port). Step 3: Set CP 2048 IP address. 1 Touch any number button (1-4) shown as below Device No.1-4 or select by REMOTE in the touch panel menu: 2 Set up same IP address of CP 2048 with VENUS X3: Device IP: CP 2048 User Manual 24 Chapter 2 Using Your Product (2) Use series port to connect CP 2048 and VSP Step 1: Touch any number button (1-4) as below picture or by selecting REMOTE in touch menu to select the Device. Step 2: Change to VSP 5360 connecting CP 2048 com port like COM1 in NETWORK under Device Remote Menu, the step is as below figure 2. (Figure 1) (Figure 2) After being setting up, push the number button (1-4)again, the CP 2048 will be automatically connected and sync. Note: If CP 2048 display shows Device Unconnected, please check if the previous setup, Ethernet cable or series port connection is correct or not Edit the Input Signal Way 1: Push the buttons on [PREVIEW LAYERS] button, or through the INPUT options in the main menu (Figure 1), then enter to the SOURCE set
We Need Your Support
Thank you for visiting our website and your interest in our free products and services. We are nonprofit website to share and download documents. To the running of this website, we need your help to support us.

Thanks to everyone for your continued support.

No, Thanks